4-channel type K thermocouple thermo USB data logger

DIGITAL EARTH RESISTANCE TESTER
The ERT 580 is a rofessional Instrument? The RUGGED and O-RING sealed digital is built with all the
protection you need for outdoor use. The ERT 580 is suitable for the testing of single earth electrodes
such as lightning conductors and other small earthing systems. The resistance of conductors such as
continuity and conductor coupling joints can also be measured. Two-terminal operation measurement,
which reduces the accuracy, can also be done by shorting P and C terminals.
Earth resistance can be measured directly from 0.01 ohms up to 1999 ohms. The reading is displayed
on a large, easy to read digital display.
The ERT 580 makes measurements by passing a constant current through the device under test
(generally a conductor or low resistance) and measuring the voltage across it. The earth resistance is
then calculated by Ohm's Law.
It has an advanced circuit design that permits the instrument to operate with the minimum influence from
earth voltage and earth resistance of the auxiliary spikes. This superb instrument is powered by 6 x 1.5
volt manganese-alkaline AA batteries. The calibration of the instrument is performed with the included
test leads. Therefore, when using the supplied test leads, the accuracy does not suffer of the three-
terminal method of measurement for the most common applications..

LED INDICATIONS:
LED If the constant current of the instrument has been reached and stable, the resistance between the
electrodes is within range and the reading can be valid.
The ERT 580 is supplied complete with an instruction manual.
The test frequency of 820Hz has been chosen to avoid stray currents at power frequencies and their
harmonics. However, the ERT 580 has a built-in filter to reject unwanted signals. The batteries are
constantly being checked while in use. The case is ideal for outdoor work. With the ERT 580 earth
electrode testing, which is an important part of electrical installation and maintenance procedure, is
made easy. The ERT 580 can be used by the electrical contractor or maintenance engineer to check the
effectiveness of their type of earth electrode systems. It may be used to test in accordance with Bs7671,
Bs7430, IEC364, NFC15-100, SABS0142, VDE0413, etc.

Features:

Measures down to 0.01 Ohm.

3 Earth Ranges: 20, 200, 2000 Ohm

One test current of 2 mA RMS.

Indication if resistance of auxiliary spikes resistance is within range.

Two or three-terminal measurement.

Three-terminal measurement for earth electrode testing. Large LCD display.

Data hold function.

Calibration performed with supplied test leads (3 T fully compensated).

Measure earth voltage up to 200V AC. Simple to use and lower power.

Open loop indication with " 1 " (MSD) on display and LED Light off.

Lightweight, robust and compact design.

Low Battery Indication.

" O-Ring" Sealed case for outdoor usage and better protection. Standard accessories for 3T and 2T.

TECHNICAL SPECIFICATIONS

Steps of 0.01 Ohm

Earth Resistance Ranges Steps of 0.1 Ohm Steps of 1 Ohm 0-19.99 Ohm 0-199.9 Ohm 0-1999 Ohm Accuracy of earth resistance (of RDG) 1.5%- dgt

Test Current (reversing DC) (820Hz?Hz) 2mA AC voltage range (sine 40-60Hz) 0-199.9V Accuracy (% of full scale) 1?1 dgt

Maximum output voltage (E-C) 0-30V Battery (AA pen light) 6 ERT 580

High Performance Review: PERFORMANCE SELECTION At a glance Measures low earth resistance Rejects interferences

Measures earth electrodes directly Indicates if resistance of auxiliary spikes in within tolerance.

Over voltage protection True constant current source Allows 2 or 3-terminal testing (ext. Short)

Rugged and -Ring?sealed case 3-terminal measurement accuracy Industrial grade case Color coded test leads Meets

CE requirements & IEC 1010 LED indicator Crowbars Knob selection or ranges

Large digital display 6 x AA battery

Certificate: CE

Ordering information: ERT-580 Earth Resistance Tester